This USB2.0 Full Speed IC
offers a compact bridge to I2C devices. The device is an I2C
slave, capable of operating up to 3.4MBit/s, with low power
consumption (8mA). The FT200XD includes the complete FT-X series
feature set and enables USB to be added into a system design
quickly and easily over an I2C interface.
Features:
- Single chip USB to I²C interface.
- Entire USB protocol handled on the chip. No USB specific
firmware programming required.
- Fully integrated clock generation with no external crystal
required plus optional clock output selection enabling a glue-less
interface to external MCU or FPGA.
- 512 byte receive buffer and 512 byte transmit buffer utilising
buffer smoothing technology to allow for high data throughput.
- FTDI's royalty-free Virtual Com Port (VCP) and Direct (D2XX)
drivers eliminate the requirement for USB driver development in
most cases.
- USB Dedicated Charger Port (DCP) detection. May be used by
mobile devices to detect the presence of a charger on the USB port
for higher current / faster charging of batteries.
- Device supplied pre-programmed with unique USB serial
number.
- Supports bus powered, self powered and high-power bus powered
USB configurations.
- Integrated +3.3V level converter for USB I/O.
- Low operating current of 8mA (typical) and
USB suspend current of 125uA (typical) current.
- Low USB bandwidth consumption.
- UHCI/OHCI/EHCI host controller compatible.
- USB 2.0 Full Speed compatible.
For sales and technical development support from our in-house
engineering team, please contact the Alpha Micro
team.
- Fully integrated 2048 byte Multi-Time-Programmable (MTP) memory
for storing device descriptors and CBUS I/O configuration.
- 512 byte receive buffer and 512 byte transmit buffer utilising
buffer smoothing technology to allow for high data throughput.
- Configurable CBUS I/O pin.
- USB Dedicated Charger Port (DCP) detection. May be used by
mobile devices to detect the presence of a charger on the USB port
for higher current / faster charging of batteries.
- Device supplied pre-programmed with unique USB serial
number.
- Supports bus powered, self powered and high-power bus powered
USB configurations.
- Integrated +3.3V level converter for USB I/O.
- True 3.3V CMOS drive output and TTL input (Operates down
to 1.8V with external pull ups and is also 5V tolerant)
- Configurable I/O pin output drive strength.
- Integrated power-on-reset circuit.
- Internal 3.3V/1.8V LDO regulators
- Low operating current of 8mA (typical) and
USB suspend current of 125uA (typical) current.
- Low USB bandwidth consumption.
- UHCI/OHCI/EHCI host controller compatible.
- USB 2.0 Full Speed compatible.
- Extended operating temperature range: -40°C to 85°C.
- Compact Pb-free 10 Pin DFN package (RoHS compliant)

Part Number |
Description |
Pack Size |
FT200XD-R |
10-pin DFN single chip USB to I2C interface IC, Revision D |
Reel of 5000 |
FT200XD-T |
10-pin DFN single chip USB to I2C interface IC, Revision D |
Tray of 490 |
Breakout Development Modules |
UMFT200XD |
USB to I2C with four control bus lines, 3.3V power out limited
to 50mA and 5V with as safety fuse. I2C signals available via
8 pin female connector. |
Each |
UMFT200XD-NC |
USB to I2C with four control bus lines, 3.3V power out limited
to 50mA and 5V with as safety fuse. I2C signals available via 8
pads on the PCB |
Each |
UMFT200XD-WE |
USB to I2C with four control bus lines, 3.3V power out limited
to 50mA and 5V with as safety fuse. I2C signals available via
8, 6" flying leads connected to the PCB pads. |
Each |